16 The boiler should only be installed with a flue system supplied by MTS (GB) Limited. The installation accessories described in the following list are included in the boiler pa.ġ8 1 2 A A Fig.
sink waste - proprietary fitting) 4.ġ7 Please check that you are familiar with the installation requirements before commencing work (Section 10). External termination of condensate draina ge pipe via internal dischar ge branch (e.g. sink waste) and condensate siphon iii) Terminating into a gully, below the grid level but above the water level.ġ6 10. External termination of condensate drainage pipe via internal dischar ge branch (e.g. Internal termination of condensate drainage pipe to internal stack 2. Connection should be via a 3 amp f used double-pole isolating switch with a contact separation of at least 3 mm on both poles.ġ5 10. 8 54 54 54 54 JK L M N I JK L M N 32 296 141 289 2 1 720 691,5 121,5 I 172,5 4,7 All dimensions in mm With packaging : 24 kW : 34 kg.ġ3 Reference Standards In the United Kingdom, the installation and initial start up of t he boiler must be by a CORGI Registered installer in accordance with the installation standards currently in effect, as well as with any and all local health and safety standards i.ġ4 I t must also be possible to be able to completely isolate the appliance electrically. Hydraulic data 440 450 mini pour entretien Fig. Steel chassis complete with expansion vessel 2.
ARISTON RECORDS FREE
K eep pressing the “Prog” button until a free memory location is shown in the display “– –:– –”.ġ1 1.
Each switching time takes up one memory location. h m Day M anual switch S ummer and w inter time setting Reset E nter w eekday/s E nter the hours W eek- d ays flash E nter min.ġ0 Entering the switching times Y ou have 20 memory Iocations available.
Setting the time c loc k (contin ued) P r o g. To set the time To set the time of day, grasp the outer edge of the dial and turn slowly clockwise until the correct time is lined up with the arrow C (Fig.ĩ 6. An override switch is located on the clock B (Fig 4). Each tappet represents 15 minutes A (Fig. General layout The mechanical clock covers a 24 hour period. W hen the anti-freeze comes on, one of two codes will be displayed with the snowflake pictogram. Check the pressure in the central heating system is above 0.7 bar and below 1.5 bar with the pressure gauge 16 (fig.1), should it be neccessary to re-pressurise the system,ensure the filling loop 45 (fig.ħ Anti-freeze and anti-sieze modes Provided the ON/OFF button is on (green light), the water pressure is adequate and the boiler has not shut down due to an error, the anti-freeze and ant-sieze operations will remain active. Ho w to Use Switching on and filling instructions 1.
ARISTON RECORDS PLUS
Cylinder Hot water start button and temperature setting (System Plus only) 31. Reset push button and red indicator locking light 30. On/off push button and power on indicator light 29. Contr ol panel 31 27 26 35 29 Fig 1 34 32 33 Control panel (fig. It has electronic ignition and is suitable for all modern electrical control systems.ĥ USER’S INSTR UCTIONS 1. It is a room sealed, fan assisted, balanced flued appliance providing central heating. Ĥ INTRODUCTION The System A is a fully automatic, wall mounted, low water content condensing system boiler.
ARISTON RECORDS CODE
Ģ These instructions are suitable for the System A boilers : MTS supports Benchmark, the heating industry code to ensure the correct installation, commissioning and servicing of domestic central heating systems.ģ C USTOMER CARE Page G uarantee. System A 24 RFFI System A 30 RFFI Installation and Servicing Instructions T ype C Boiler s G.C.N: 47-116-14 (24 kW) G.C.N: 47-116-15 (30 kW) LEA VE THESE INSTR UCTIONS WITH THE END-USER S S Y Y S S T.
0 kommentar(er)
